Maven Automation

There are various uses of LT Control Panel as per the user requirement, the main being as Control Center or Feeder or Distribution Board.

LT Power Panel receives the main power supply Either from Generator or Transformer and distributes the same to various electrical devices and distribution boards.

With the help of protective switch gears, they are used for controlling and monitoring the main power supply from a centralized location.

There is various application of LT Control Panel. Some of them are listed as:

• Hospitals
• Educational Institutions
• Commercial Complexes
• Hotels

A MS Lighting Distribution Board (LDB Panel) is comprised of a free-standing enclosure, a bus bar system, MCCB's, metering and support equipment’s and required current transformers.

Panels are assembled in a systematic manner such as incomer section and outgoing section.

A MDB is comprised of a free-standing enclosure, a bus bar system, MCCB's, metering and support equipment’s and required current transformers.

• Index of protection: IP 31 & IP 54
• Ample cabling space for easy connections
• Panels for front or rear access to suit application
• Top and bottom cable entry.
• Floor mounting
• Modular system with Customized design to meet end user requirements.
• Maximum safety & reliability

An MDB is a panel or enclosure that houses the fuses, circuit breakers and ground leakage protection units where the electrical energy, which is used to distribute electrical power to numerous individual circuits or consumer points, is taken in from the transformer or an upstream panel.

An MDB typically has a single or multiple incoming power sources and includes main circuit breakers and residual current or earth leakage protection devices.

A MDB is comprised of a free-standing enclosure, a bus bar system, MCCB's, metering and support equipment’s and required current transformers.

Panels are assembled in a systematic manner such as incomer section and outgoing section.

MS Power Distribution Board is a system, consisting of a Main Distribution Board (MDB), Sub Main Distribution Boards (SMDBs) and Final Distribution Boards, by which the electrical energy is transmitted via branches to reach the exact end user.

• Ample cabling space for easy connections
• Top and bottom cable entry.
• Panels for front or rear access to suit application
• Index of protection: IP 31 & IP 54
• Floor mounting
• Maximum safety & reliability
• Modular system with Customized design to meet end user requirements.

Instrumentation Panels are useful to monitor and control process parameters like temperature, pressure, flow etc.

Input signal from the sensors is connected to the panels through isolation or compensating cables.

The output from the panel is connected to the final control element for controlling the process value. Various interlocks and safety audio visual alarms are provided through Alarm Annunciator For PLC's. Total process simulation can be shown on.

Reactive Power compensation system is designed to work automatically on LT power supply to measure, display & connect, disconnect the required capacitor banks through Thyristor /Capacitor Duty contactor with protection of MCB / HRC Fuses & series reactors to each bank to achieve the set Target power factor.

Thyristor /Contactor Switched Automatic power factor system is the highly accurate, properly designed system with required creep age distance as per required standards. APFC System equipped with advanced, Digital Microprocessor based relay to measure, calculate and display all electrical network parameters.

It accurately measures cycle to cycle reactive power requirement for required capacitors are connected to switching element / device installed in the system, so as required capacitors are connected / disconnected to the network. APFC Controllers close loop fast response multi method switching [MMS] algorithm helps system to have close & precise control on power factor.

• Modular Structure
• Protection to each step.
• Well ventilated design.
• Powder coated metallic frame structure design
• Four modes of operation.
• Door interlocks Facility.
• Good Service Backup.

Power Control Centre are the most essential part of electrical system of an industry from where the power of the industry is controlled.

Power Control Centre is a power distribution board to control the Electrical power supplied to HT Panels, MCC panels and transformers who play vital role in all electrical control system.

Power Control Centre is used for distribution and control of various power source used in industry. Normally Power Control Centers is installed near power source hence fault level is high.

Various protections viz short circuit, overload, earth fault, under voltage etc. are provided to protect source and equipment. Power Control Centre widely used in refineries, chemical plants, pharmaceuticals and Solar Industries.

Direct on-Line start is probably the simplest and traditional type of start and it is to connect the motor directly to the power supply performing therefore a full-voltage start-up.It is often abbreviated with the acronym DOL.

DOL (Direct on Line) start is the simplest and most cost-effective system for starting pumps and motors and it is traditionally the most widely used. The induced current is the rotor is high. This results on a peak current on the network which can be 5 to 8 times the nominal current.

They are suitable for startup of small submersible pumps, deep well pumps or booster sets with surface pumps.


DOL control panels need a direct connection to the power supply network, which implies:

• Start at full voltage and constant frequency
• High starting torque
• Very short acceleration times.

Star Delta starting is the best known and perhaps the most widely used low voltage starting method. It is used to start the pump's motor with lower levels of mechanical stress and with current limitation during start-up; it does this with the aid of a timed system which switches the control contractors installed inside the panel.

Star-delta starting reduces starting current and torque to values of 33% (1/3) of those measured during direct starting. During start-up, the current flowing through components are lower than the motor rated current

Three Phase Mimic Panel are being used in the industry for many years to display process status and alarms. In Mimic Panels, the process is pictorially represented on the front side of a Control desk / Panel.

Generally, mimic displays are printed on polyester or polycarbonate sheets and provided with an acrylic front sheet for protection. LEDs and other Indicators can be fitted on the display for Process Indication.

At CSE Solutions, we supply conventional and mosaic mimics and annunciator panels with MS powder coating, stainless steel enclosures furnished with the internal wiring of Mimic LEDs and Annunciator Windows. We have an in-house team of designers to design the Mimic Display as per our client’s process layout.

Programmable logic controller (PLC) control panels or also known as PLC Automation Panel are one of the most important and efficient kinds of control panels. Which are generally used in variety of electronic and electrical circuit fittings.

PLC Control Panels we manufacture are highly capable of giving higher output at less power consumption. Integrated with solid PLC logic and flawless PLC hardware programming.

Ease in modification of logic, reduced size, means of remote communications and advances in the technology have made PLC Automation Control Panels an edge over conventional relay-based systems. Our Engineers has provided PLC based Panels from Various PLC.

From small I/O application to the complex I/O systems are provided by the Maven Engineers. Maven Engineers have developed communication software's for remote communication of the PLC Panels in various different protocols.

With PLC based Panels HMI/MMI are provided to provide the operator various messages and controls of the process plants touch screen MMI are provided. To effective control of the system.

PMCC- Power cum Motor control Center panels are combination of Motor Control Center-MCC and Power Control Center-PCC panel.

The MCC Panels are used in industrial and commercial applications for connecting the individual motors for manually, remotely or automatically starting, stopping selecting forward and reverse rotation, selecting and regulating the speed, regulating and limiting the torque and protecting against overload, single phasing, phase imbalance, earth fault, under current, under / over voltage, lock rotor current, high winding temperature etc.

The PCC Panels are the most essential part of electrical system of an industry from where the power of the industry is controlled. PCC Panel is a power distribution board to control the Electrical power supplied to HT Panels, MCC panels and transformers who play vital role in all electrical control system.

Power Control Centre is used for distribution and control of various power source used in industry. Normally Power Control Centers is installed near power source hence fault level is high.

Power Control Centre is used for distribution and control of various power source used in industry. Normally Power Control Centers is installed near power source hence fault level is high

The panel receives information from devices designed to detect and reports fires, monitors their operational integrity and provides for automatics control of equipment, and transmission of information necessary to prepare the facility for fire based on a predetermined sequence.

At maven Automation, we offer a range of individual or combined of Fire Fighting Control Panel - Fire Alarm Control Panel (FAC Panel). Our product comes with standard features.